主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

Flow separation control on swept wing with nanosecond pulse driven DBD plasma actuators

A 15° swept wing with dielectric barrier discharge plasma actuator is designed.Experimental study of flow separation control with nanosecond pulsed plasma actuation is performed at flow velocity up to 40 m/s. The effects of the actuation frequency and voltage on the aerodynamic performance of the swept wing are evaluated by the balanced force and pressure measurements in the wind tunnel. At last, the performances on separation flow control of the three types of actuators with plane and saw-toothed exposed electrodes are compared. The optimal actuation frequency for the flow separation control on the swept wing is detected, namely the reduced frequency is 0.775, which is different from 2-D airfoil separation control. There exists a threshold voltage for the low swept wing flow control. Before the threshold voltage, as the actuation voltage increases, the control effects become better. The maximum lift is increased by 23.1% with the drag decreased by 22.4% at 14°, compared with the base line. However, the best effects are obtained on actuator with plane exposed electrode in the low-speed experiment and the abilities of saw-toothed actuators are expected to be verified under high-speed conditions.     

Specific grinding energy and surface roughness of nanoparticle jet minimum quantity lubrication in grinding

Nanoparticles with the anti-wear and friction reducing features were applied as cooling lubricant in the grinding fluid. Dry grinding, flood grinding, minimal quantity of lubrication（MQL）, and nanoparticle jet MQL were used in the grinding experiments. The specific grinding energy of dry grinding, flood grinding and MQL were 84, 29.8, 45.5 J/mm³, respectively. The specific grinding energy significantly decreased to 32.7 J/mm³ in nanoparticle MQL. Compared with dry grinding, the surface roughness values of flood grinding, MQL, and nanoparticle jet MQL were significantly reduced with the surface topography profile values reduced by 11%, 2.5%, and 10%,respectively, and the ten point height of microcosmic unflatness values reduced by 1.5%, 0.5%,and 1.3%, respectively. These results verified the satisfactory lubrication effects of nanoparticle MQL. MoS₂, carbon nanotube（CNT）, and ZrO₂ nanoparticles were also added in the grinding fluid of nanoparticle jet MQL to analyze their grinding surface lubrication effects. The specific grinding energy of MoS₂ nanoparticle was only 32.7 J/mm³, which was 8.22% and 10.39% lower than those of the other two nanoparticles. Moreover, the surface roughness of workpiece was also smaller with MoS₂ nanoparticle, which indicated its remarkable lubrication effects. Furthermore,the role of MoS₂ particles in the grinding surface lubrication at different nanoparticle volume concentrations was analyzed. MoS₂ volume concentrations of 1%, 2%, and 3% were used.Experimental results revealed that the specific grinding energy and the workpiece surface roughness initially increased and then decreased as MoS₂ nanoparticle volume concentration increased.Satisfactory grinding surface lubrication effects were obtained with 2% MoS₂ nanoparticle volume concentration.     

前缘参数对翼型气动-隐身特性敏感性分析

针对翼面部件对隐身飞机气动和隐身性能影响更为突出的问题,提出了一种翼型前缘参数化修形方法,采用高精度气动和电磁数值计算方法,进行了前缘形状对翼型气动-隐身特性的敏感性分析。研究结果表明:翼型前缘半径增加,其最大升力系数、失速迎角、最大升阻比显著增加,但其前向RCS均值也增加明显,设计时需进行综合权衡;在不影响结构和装载的情况下,下表面偏角尽量小,修形长度取0.15c,对翼型的低、高速气动和隐身特性都有利。     

三维数模随动下的机翼结构重量优化

目前,基于快速建模下的重量重心估算系统得到了快速发展。为了进一步提高结构重量估算精度,研究了如何在重量重心快速分析(WCGA)系统环境中构建优化模块。以机翼结构重量优化为例,提出优化流程,对优化模块功能进行分解,给出模型简化要求。以A320飞机机翼为例,对梁和长桁进行优化,结果显示,经过优化,有效减轻了结构重量,且相比于传统的减重优化设计方法,极大提高了计算效率。     

基于LQG/LTR的飞翼飞机阵风减缓系统研究

根据我国《运输类飞机适航标准》的要求,采用有理谱逼近的方法建立了Von Karman大气紊流的数值仿真模型;详细推导了多变量系统鲁棒性的衡量方法,给出了开环系统奇异值曲线形状与闭环系统鲁棒性的关系;针对飞翼飞机多操纵面的特点,将控制分配技术与LQG/LTR控制器结合在一起,同时兼顾了对飞机过载和翼根弯矩的减缓。仿真结果表明,所设计的控制系统在对飞机过载减缓的同时,也对机翼的翼根弯矩进行了有效的减缓。     

M40/4211 复合材料层合板铣削加工试验

通过分析碳纤维复合材料的性能特点及对切削加工性能的影响,提出了铣削刀具材料和几何结构形式的选用原则,介绍了几种适于碳纤维复合材料铣削的加工刀具。针对碳纤维复合材料中常用的M40/4211复合材料层合板进行加工缺陷试验和切削试验,总结出影响M40/4211复合材料层合板加工质量的因素及规律,得到每种刀具加工M40/4211复合材料层合板的最佳加工参数,较高的切削速度配合恰当的进给速度可以有效提高M40/4211复合材料层合板的加工质量和加工效率。     

测量兆欧表中值电压和开路电压的一种方法

提出了一种仅用一台通用高阻标准器和台式数字多用表来完成兆欧表中值电压和开路电压的计量方法。通过调节高阻标准器的阻值以及改变和数字多用表的连接方式,组合出所需的测量电路。实验结果表明,该方法实用性强,操作方便,灵活度高,减低了成本,提高了设备的使用率。     

国产高档数控系统在航空领域的应用与性能分析

基于目前国产数控系统在航空结构件加工中的实际运行情况以及在使用过程中暴露出的问题,详细统计并分析了国产数控系统在航空结构件加工中的应用现状和综合性能。结合"工业4.0"发展理念,探讨了面向航空领域国产数控系统对航空企业实现智能化制造的意义和未来发展。     

机场容量利用及流量分配优化策略

为了充分利用机场容量,减少航班延误,需要合理分配进离场流量。以机场容量作为约束,以进离场航班总延误成本最小作为目标,建立进离场流量分配优化模型。构建随延误时间呈超线性增长的延误成本计算公式,引入航班进离场延误成本权重系数作为不同进离场优先级的决策偏好信息。用动态规划法求解模型,并引入最优决策候选集合的概念,缩小计算过程中的搜索量,减少计算时间。算例结果分析表明,方法可以在机场容量约束下得出进离场流量分配的最优策略,使得航班总延误成本最小,并且快速计算可以满足实时决策支持的要求。